Page c1
C 152
Return to whittsflying Home Page

Flying the C-152 pattern Cessna's way; …About the Cessna 152; ...Calibrating C-152 trim; ...Short field Takeoff; ...Soft-field Takeoff; ...Spins; ...Traffic Pattern; ...Go-around full flaps; ...Short Field Landing; ...Soft Field landing; ...Crosswind Landing; ...Takeoff and departure Stall; ...Approach to Landing Stall; Approach to Landing Stall by Cessna FBO; ...C-152 Procedures; ...C-152 Checklist; ...Inflight Emergency Procedures; ... Committed to a Forced Landing; ...Inflight Fires; ...Icing; ...Normal Landing; ... Short field landing; ...Baulked Landing; ...After Landing; ...Securing Aircraft; …Aircraft Basic Knowledge Sheet; ...Calibrated vs. Indicated Airspeeds; …Flying Safer; …C-152 Spin Opinion; …C-152 Approach Speed Opinion; …

Flying C-152 Patterns Cessna's way

Last week (9-7-99)I failed a checkride at a certified Cessna Agency in a C-152. I was surprised to find out that with judicious use of initial trim setting for takeoff and power, it is Cessna's standard instructional procedure to negate any use of trim. The C-152 can be leveled from climb at 80 knots just by a reduction in power to 2200 rpm. No trim necessary. The abeam the numbers reduction of power to 1600 and the first ten degrees of flaps gives an approach speed of 70 knots and power at 1500. No trim necessary. The addition of flaps in the turns gives sufficient lift/drag to make this one power setting applicable for the whole descent. The base turn is accompanied by the second notch of flaps. Result is an approach speed of 65-knots. No trim necessary. The full flap condition is applied in the turn to final.and the speed drops to 60 knots for the final approach. Keep 60-knots into the roundout and flare at 54 knot by keeping the nose slightly below the end of the runway. By letting students see where they are going we keep them from being frightened..

Insult was added to injury when I found that the C-172N could be flown and landed the same way. according to Cessna I have been flying their aircraft incorrectly for over 30-years. Even my first instructor, who became a factory representative for Cessna, taught me incorrectly by emphasizing the use of trim. This old-dog has learned a new trick. Oh, lordy, I have seen the error of my ways and have a ton of repenting to do. Where was Arenias when I needed him?

Transcript of most of the C-152 checkride is on Page 4. Instructors learn much more….

About the Cessna 152
C-152 Information
http://www.cessna15-152club.com
You should be warned about flying in a different kind of aircraft. There is just enough difference in a C-152 to create stress and interfere with your thought processes. The engineering of the C-152 is similar to the 150 except that where maximum flaps are only 30 degrees a 1/2 turn of trim seems sufficient for each 10 degrees of flap. After landing and flaps up, the aircraft is properly trimmed for climb. The C-150 is trimmed for level. Your use of the trim may produce a different result.

Cessna in a 152 Owners Advisory Letter has indicated that a C-152 which is run at full rich will result in a 40% increase in consumption along with a 70 minute reduction in flight time. The same figures would probably apply to other Cessnas.

Get a complete breakdown of how a C-150 and C-152 differ. Trim, flaps, electrical, and speeds. Go up and review all the airwork in a strange aircraft before doing any landings.

Calibrating C-152 trim

C-152 to get 1500 you need to reduce to 1600 (similar to C-172's 1700). At altitude and imaginary numbers, power to 1600, hold altitude and heading until reaching 60 knots. Now quickly trim for hands-off but be sure to keep track of how much is required. Do the same for each 10 degrees of flap as you descend. Trim is added or put on by moving the wheel top down to bottom. Trim is taken off by moving The trim bottom to top. The best way to remember the trim setting is to predicate the movement of the trim from a constant power setting. You may need to do this a couple of times. You are trying to index the flap-trim ratios required to maintain 60 knots. Once you have developed a stabilized procedure for maintaining 60 knots you should be home free.

We will begin from level cruise and reduce power to 1500 while holding heading and altitude. The Airplane will decelerate and the rpm will fall to 1300. We will experiment with the number of trim turns and find that it takes to five turns to descend at 60 knots hands-off. When descent is about to commence at 60 knots we will put in 10 degrees of flaps,. Apply slight forward pressure with our thumb to maintain 609 knots and then take off one turn of trim. We will repeat this again twice more with additional 10 degrees of flaps so that we will have 30 degrees of flaps and will have removed three of the five initial turns of trim.

After doing this on a constant heading, we will make left and right 90 degree turns and then put in flaps to 20-degrees and trimming for 60-knot descent hands-off and making left and right 90 degree turns. Now we will put in the full 30-degrees of flaps and record the trim change required for the 60-knot final approach. The entire process will be repeated again from the beginning with right and left 90-degree turns. Once this is determined we will repeat the process from the beginning to confirm our settings.

For the go-around we will find that the addition of power and removal of flaps will have the aircraft trimmed for a relatively low speed climb. Take off one turn of trim for a 70 to 80 knot climb. At the application of power you must anticipate with right rudder to hold the nose in line with the runway. Forward pressure with the hand (Not just the thumb) is required to avoid an abrupt pitching up and to allow the aircraft to accelerate. At 70 knots relax the forward pressure and allow the number to seek its trimmed attitude and airspeed. Remove trim for the climb speed you desire. At the peak of our climb we want to 'calibrate' the trim required in transitioning from the climb to level cruise as it will exist with the power reduced. This will take several tries.

The last step in our calibration is to determine just where the trim is set when we add full power and remove the flaps. The aircraft should be trimmed somewhere between level flight and Vy climb. We will determine the amount of trim required and use that as one of the trim setting changes we make during the go-around in anticipation of climbing at Vy. Once the calibration is completed we have determined the landing procedure that will enable us to anticipate the power, flap and trim settings required for the standard stabilized approach.

CESSNA 152
From 65kt climb
LEVEL OFF 2 TRIM UP

DESCENT
CH-1700 RPM
10 DEGREES FLAPS 1/2 UP TRIM
20 DEGREES FLAPS 1/2 UP TRIM
30 DEGREES FLAPS 1/2 UP TRIM

Short Field Takeoff:
Flaps set at 10 degrees. Release brakes and accelerate on the runway centerline. At 54 KIAS, the nose of the aircraft is raised smoothly and quickly to Vx pitch attitude - maintain 54 KIAS.

Establish normal climb 70-80 KIAS and retract the flaps. Since the Vy speed will vary with weight, it might be better to use the lower 70 KIAS when solo and 80 with two aboard. An old FAA manual once said that flap retraction should be made only after passing through 200'.

C-152
Short field
Brakes locked, full power, 10 degrees flap
Vx is 54 kts for best angle
Retract flaps at 60 kts and get Vy of 67 kts
The C152 take-off distance decreases by 10% for every 9kts of headwind component

Soft Field Takeoff:
Flaps set at 10 degrees. Elevator control to full nose up position. As the nose of the aircraft comes up to Vy pitch attitude, release elevator pressure as necessary to Maintain a maximum nose high attitude just short of dragging the tail. Level close to Vy airspeed before attempting to climb out of ground effect. Fly as close to the ground as you can. This will maximize your effective engine power and speed up acceleration. Ground effect ceases at 1/2 wing span altitude. With a 32' wingspan you have 16' of ground effect. The wing is already over 5' above the ground. Any altitude of the wheels over 11' will degrade aircraft performance. Stay low, accelerate and then climb.

If necessary, establish climb at 54 KIAS to clear any obstacles. If not, normal climb 70 - 80 KIAS based on weight. The FAA test does not include both a soft-short field requirement so the recommendation for airspeeds is good. In the FAA PTS guide you should accelerate to the 70 - 80 KIAS before climbing.

Retract flaps once clear of obstacles or when normal climb speed is established. 200' is former FAA recommendation before flap retraction.

Spins
In less that two turns you can recover just by letting go of the controls. beyond two turns to the left you must make a normal spin recovery. It is possible to tell which rudder will effect a spin recovery by deciding which rudder is harder to push.

Traffic Pattern.
Normal climb airspeed (67-70 KIAS) should be maintained as should full power.

Opposite the proposed touchdown point on the runway, apply carb. heat, then reduce power to approximately 1600 RPM Plane will decelerate to 60 knots and 1500 rpm. Trim for hands-off.

Apply 10 degrees flap and trim the aircraft for a 60 KIAS glide. in the 1990s you should not leave pattern altitude until turning base. Noise abatement procedure suggests not leaving pattern altitude until turning base. Try to keep the neighbors happy.

Turn base leg when runway numbers are at a 45-degree angle behind wing. This point may vary with wind conditions. The deceleration of Cessnas when the power is reduced to settle at 1500 RPM and altitude and heading are maintained the 45 degree or "key" position is nearly automatic. The "key" position has been dropped as a term by the FAA. The quickness used to go though the procedures should be faster as winds become stronger.

Bring the flaps to a 20-degree position, and retrim the aircraft to maintain 70 KIAS. The base leg is where you decide to widen out, square your pattern or angle toward the runway as a first choice. Second choice would be putting in additional flaps if high. After these decisions have been tried then change power. You should try to keep as many "constants" in your approaches as you can.

Lead the turn to final so as to roll out on the extended centerline. Accuracy in final alignment is directly related to how well the downwind was flown according to wind conditions. Even slight crosswinds on the ground must be considered as being stronger at altitude. Never exceed a 30-degree bank in the pattern. Standardized 30-degree banks will allow you to make all your turns more accurately. A 30-degree bank only increases the G force by .15. A shallower bank extends the "blind" time in the turn.

Apply full flaps (30 degrees) as needed and establish 60 KIAS glide. (trim as needed) The normal Cessna landing is made with full flaps. Full flaps improve landing accuracy. Crosswind or strong gusty winds are the only justification for using minimal flaps. C-152s can be slipped with flaps according to the POH.

About 1970 the FAA came out with a recommendation that power off landings not be considered "normal" Many instances of inability to re-apply power were occurring. The FAA now recommends that power be maintained into the actual flare and only be taken off at actual touchdown. Plan your approaches with the understanding that power will be applied. Then if power is lost, the removal of flaps will allow a safe power off landing.

I recently was shown that Cessna designed the C-152 so that it could be climbed at 70-75 knots at full power, leveled off at pattern altitude without the use of trim merely by reducing the power to 2200 rpm. This gave a downwind of 80 knots. (I thought it was inconsiderate of faster aircraft.) Abeam the numbers the descent could begin just by reducing power to 1500 and flaps added to make the aircraft fly at 70 knots at 1500 rpm. No trim necessary. The next ten degrees of flap could be added during the base turn and the speed become 65 knots. Full flaps added during the turn to final would give an approach speed of 60 knots. Further power changes were used to adjust the approach slope.

The landing and flare began at 60 knots and slowed to 54 knots. The nose was held relatively flat so that the student could see the runway. Nose up was limited so that the student could see the end of the runway. My ability to fly a heading was not done well at all. I flew well to the right. There was a LOC approach reciprocal to the selected heading which

I thought justified my misdirection. Apparently not.

Steep turns are performed at 80 knots with power added during the turn to maintain the 80 knot airspeed. I did not do well on the steep turns until I did them at cruise. Power off stalls are only performed with full flaps as though landing. The stall break must be fully developed before recovery.

Go-Around, Full flaps

Full power, carb heat cold. Lock arm to hold the yoke firmly forward to prevent pitch up and anticipatory right rudder to counteract P-factor. Establish level pitch attitude while bringing the flaps up. Milking flaps up or by notches at speeds below 60 is best way. Climb on reaching Vy.

Short Field Landing
The traffic pattern for a short field landing is flown the same as a normal landing traffic pattern up to the final approach.

On final approach, establish a full flap, power on descent at 54 KIAS. Power setting should be adjusted as necessary to establish a glide path, which will bring the aircraft just above any obstacles.

Once it is apparent that the aircraft will clear the obstacle without power, slowly close the throttled and maintain 54 KIAS. Maintain 54 KIAS down to the flare and land the aircraft with a minimum amount of float.

Once the aircraft is on the ground, retract flaps, lower the nose gently, and apply smooth but firm brake pressure.

Note: If the final approach on a short field landing is properly planned and executed, final approach will not involve any additions of power. A lower approach speed can be used at lower weights.

Soft Field Landing:
The traffic pattern is flown just as it would be for a normal landing until final approach. On final, a 60 KIAS full flap glide is established.

Once the runway is assured reduce power to idle RPM and flare normally over the runway. Increase the pitch attitude prior to touchdown and bring power up to 1200 or 1500.

Once the main gear touches the runway, continue back elevator pressure as required to keep the nose wheel off the runway while bringing up the flaps. Removal of the flaps will allow the pitch attitude to increase.
Keep the power on sufficient to keep the nose off. With proper power application it is possible to taxi clear of the runway without the nose wheel touching.

Crosswind landing:
Crosswind landing involve flying a crabbed traffic pattern with one addition. On final approach, when the aircraft is aligned with the runway centerline, the aircraft will begin to drift. The upwind wing is lowered to the point where the aircraft stops drifting and (the wing) is maintained in this down position. Rudder pressure is applied in the opposite direction of the aileron deflection to keep the aircraft nose/tail lined up with the runway centerline. Pressure must be maintained on both controls in order to keep the aircraft so aligned. 20 degrees of flaps rather than full flaps may be used on final, depending on wind strength and (crosswind angle) component with the runway. touchdown is accomplished with the upwind wheel of the main gear touching the ground first. Once on the ground, apply increasing upwind aileron gradually to full aileron, and maintain directional control with the rudder pedals. I would make several suggestions. Select your flap setting early on the approach before turning final. 20-degrees of flap would be the maximum used for a 10-kt crosswind. Maintain your approach speed by lowering the nose as you establish your cross-control configuration. On touchdown, hold the yoke well over. The wing will not touch if the plane is kept rolling straight.

Takeoff and Departure Stall:
Clear area
Carb heat on
Reduce power to 1500 RPM
Slow aircraft to lift-off speed (55 KIAS)
Apply full power when reaching lift-off speed and increase backpressure firmly on the elevators until the stall occurs. Right rudder pressure must be used to overcome P-Factor. When introducing this stall limit power increase to 2000 RPM. Full power applications during "Proficiency".

If the stall is to be done while in a turn, a bank angle of approximately 20 degrees should be established when lift-off speed is reached. Coordinated control pressure should be utilized as necessary to maintain this bank angle until the aircraft stalls. Limit bank to 20 degrees regardless. A higher angle of bank greatly exaggerates the effect of uncoordinated controls.

Recovery:
Release the backpressure and level the wings utilizing coordinated control. Allow nose to fall to or slightly below the horizon. Then apply full power for the recovery at Vy climb.

Approach to a Landing Stall:
Clear the area .
Carburetor heat
Reduce power to 1500 RPM and when airspeed is in the white arc, apply full flaps and establish a 60 KIAS glide.

If the stall is to be done in a turn, establish a 20-degree bank angle. Any bank beyond 20 degrees can be a prelude to a full flap spin. Close the throttle slowly, gradually increase backpressure until the stall occurs. Power can also be left at 1500 RPM.

Recovery:
Release back pressure, apply full power and level wings using coordinated control. Get the nose down to level flight. Lock your elbow against the door to prevent abrupt pitch-up as full power is applied.

When airspeed is on the upgrade retract flaps to 20 degrees without allowing sink to occur. At 60 knots remove rest of flaps and climb.

Approach to Landing Stall by Cessna FBO
The traditional approach to landing stall has been transmorgified into a power-off stall in landing configuration. It requires that you enter an approach to landing with full flaps and power off and then at some point you stop the descent until you stall. as though you were attempting to extend your glide distance just by raising the nose while entering the base turn to final. The assumption is that the student cannot add power nor can he do anything except concentrate on an outside reference point beyond the glide range of the aircraft. While such a scenario can be made to occur using the latest Cessna landing program, it is most unlikely to occur to a student who had been taught the traditional stabilized constant airspeed approach.

The recognition of the stall and the recovery from the situation is the instructional objective. The required recovery procedures is that the pilot break the angle of attack, apply full power, level the wings and begin to reduce the flap extension. On reaching climb speed, the climb begins and the cleanup is completed.

CESSNA 152 Procedures
60 KT FULL FLAP TRIM HOLD HEADING GIVES 65 KT CLIMB TRIM 1 FULL TRIM UP
LEVEL OFF 2 TRIM UP FINE TRIM 60 KTS
1500 RPM-C.H. 1700 RPM +8 COUNT FLAPS-30 DEGREES
4 FULL TRIM DOWN=60 KT ANTICIPATE w/HEAVY FWD YOKE
10 DEGREES 1/2 UP TRIM HOLD HEADING
20 DEGREES 1/2 UP TRIM FINE TRIM 60 KTS
30 DEGREES 1/2 UP TRIM

C152 Checklist

Pre-flight Inspection

Cockpit
Log book
"AR(R)OW" documents
Control lock
Shut off ON
Ignition OFF
master switch ON,
full flaps,fuel gauges, fan
master switch OFF
Fuselage, rear
fuel drain
fuselage
empenage
rudder gust lock
rear tie down
Right side fuselage
right side fuel drain
Right wing
flap
aileron (
wing walk around
main gear
wheel chock
wing tie down
Fuel VISUALLY
Fuel Cap,
Nose
Engine Oil level CHECK, do not operate with less than 4 quarts
Fuel sump
Cowl
Propeller
Spinner
Air filter
Landing light
Nose wheel strut and tire
Static port
Left wing
main gear nut/cotter key)
wheel chock
wing tie down
Fuel VISUALLY
Fuel Cap
Stall warning port, pitot tube, fuel vent
wing walk around
aileron
flap,

General walk around required by FARs...

Before starting engine
Pre-flight inspection
Passengers briefed
Seats, belts, shoulder harnesses
Doors, closed and latched
Fuel shut-off valve ON
Radios and electrical equipment OFF
Brakes- test and hold
Check circuit breakers IN
Mixture -RICH
Carb heat- COLD
Prime- up to 3 strokes if cold, locked
Throttle- Open 1/2" (closed if engine warm)
Propeller area
Master switch
Beacon
Ignition
Throttle-- rpm or less
Oil Pressure
flaps
Radios
Transponder

Before Takeoff
Brakes
Cabin Doors
Flight Controls
Flight instruments
Fuel shut off valve
Mixture -- RICH (below 3000')
Elevator Trim
Run up-- Throttle to 1700 rpm
Magnetos--CHECK (drop should not exceed 125 rpms, or 50 rpm differential)
Carb heat-- CHECK for approx. 50 rpm drop
Engine instruments and ammeter
Suction gauge
Throttle to 1000 rpm or less
Radios
Strobe/Nav lights
Throttle friction
Transponder
Brakes

Normal Takeoff
Flaps up
Full throttle
rotate at 55 knots
pitch for Vy (67knots) during climb out
Short Field Takeoff
Flaps-- SET 10 degrees
Full throttle (above 3000' lean mixture for maximum rpm)
release brakes at 2000 rpm
tail slightly low, pitch for Vx (54 knots) until clear of obstacle

In Flight Emergency Procedures

NOTE: procedures for engine failure during takeoff run and immediately after takeoff are in the POH and should be memorized.
Emergency landing without engine power
Level the wings,
ESTABLISH BEST GLIDE (60 knots)
Choose a landing spot --
CHANGE COURSE TO TAKE YOU THERE
MAINTAIN CONTROL OF THE AIRCRAFT
Check the following items:
primer--CHECK in and locked
master switch---ON
ignition--SET TO BOTH
carb heat--ON
mixture-RICH
fuel shut off--ON
fuel quantity--CHECK
oil pressure/temp--CHECK

Committed to a Forced Landing

Transponder--SET to 7700 and ident
COM radio --SET to emergency frequency 121.5
aircraft type and tail number
position and altitude
problem you are having
number of persons on board
intended landing spot
Seat belts ON and SECURE
Mixture-IDLE CUT-OFF
Fuel shut off valve-- OFF
Ignition switch--OFF
Flaps--UP until landing is assured
Master switch -- OFF
Cabin doors-- OPEN SLIGHTLY
Nose hig\h-tail low
Apply brakes heavily

Ditching
Transponder--SET to 7700 and ident
COM radio --SET to emergency frequency 121.5
aircraft type and tail number
position and altitude
problem you are having
number of persons on board
Jettison or secure heavy objects in baggage area
Approach:
High winds, heavy seas--INTO THE WIND
Light winds, heavy swells--PARALLEL TO SWELLS
Flaps--30 degrees
Power-- ESTABLISH 300 ft/min DESCENT AT 55 knots
Cabin doors-- UNLATCH
Touchdown-- LEVEL ATTITUDE AT 300 ft/min DESCENT
Face--CUSHION at touchdown with coat
EVACUATE aircraft through cabin doors
Life vests and Raft--INFLATE

In Flight Fires

Engine fire
Mixture--IDLE CUT-OFF
Fuel Shutoff Valve--OFF
Master switch--OFF
Cabin heat and air--OFF (except wing root vents)
Airspeed--85 knots (or whatever it takes to put out the fire)
Forced Landing-- EXECUTE as described in Emergency Landing Without Engine Power

Electrical fire
Master switch--OFF
All other switches (except ignition switch)--OFF
Vents/cabin air/heat--OFF
Fire Extinguisher--ACTIVATE (if available)
WARNING--After discharging an extinguisher in a closed cabin, ventilate the cabin
If fire appears out and electrical power is necessary to continue flight:
Master switch--ON
Circuit breakers--CHECK for faulty circuit DO NOT RESET
Radio/Electrical switches--ON one at a time, with delay until short is localized
Vents/ Cabin Air/ Heat--OPEN when ascertained that fire is completely extinguished

Cabin Fire
Master switch--OFF
Vents/cabin air/heat--OFF
Fire Extinguisher--ACTIVATE (if available)
WARNING--After discharging an extinguisher in a closed cabin, ventilate the cabin
Land the airplane as soon as possible to inspect for damage

Wing fire
Navigation light switch--OFF
Strobe light switch (if installed)--OFF
Pitot heat switch (if installed)-- OFF
NOTE: Perform a side slip to keep flames away from fuel tank and cabin.
Land as soon as possible with flaps retracted

Icing
Inadvertent Icing Encounter
Turn pitot heat switch ON (if installed)
Turn back or change altitude to obtain an outside air temp that is less conducive to icing
Pull cabin heat control to full out to obtain maximum defroster air
Open throttle to increase engine speed and minimize ice build up on propeller blades
Lean mixture for max rpm's if carb heat is used continuously.
Plan a landing at the nearest airport. With extremely rapid ice build up, select a suitable "off airport" landing site.
With an ice accumulation of 1/4 inch or more on the leading edges, be prepared for significantly higher stall speed.
Leave flaps retracted. Flap extension could result in a loss of elevator effectiveness.
Open left window and, if practical, scrape ice from the windshiled for visibilty
Perform a landing approach using a forward slip, if necessary, for visibility
Approach at 65-75 knots depending on the amount of ice accumulation

Perform landing in a level attitude

Landings
Normal Landing
Airspeed 60-70 knots (flaps up)
Flaps-- AS DESIRED (below 85 knots)
Airspeed--55-65 knots (flaps down)
Power--REDUCE to idle as obstacle is cleared
Touch down--MAIN WHEELS FIRST
Landing roll--LOWER NOSE GENTLY
Braking--Minimum required

Short field landing
Airspeed 60-70 knots (flaps up)
flaps--30 degrees (below 85 knots)
Airspeed-MAINTAIN 54 knots
Power--REDUCE to idle as obstacle is cleared
Touch down-- MAIN WHEELS FIRST
Brakes--APPLY HEAVILY
Flaps--RETRACT

Balked landing (Go around)
Throttle--FULL OPEN
Carb heat--COLD
Flaps--RETRACT ONE NOTCH
Airspeed--55 knots
Fly over the right edge of runway for traffic visibility
Flaps--RETRACT each notch when altimiter shows positive climb

After landing
Flaps--RETRACT
carb heat--COLD
Transponder--OFF

Engine Shut down (O-235-L2C only)
Throttle--1800rpm for 18 seconds
Throttle--1200rpm
Mixture--Idle Cut off

Securing airplane
Radios and electrical equipment--OFF
Mixture-IDLE CUT-OFF
Ignition switch--OFF
Master switch--OFF
Control Lock--INSTALL
Rudder gust lock--INSTALL
Tie downs--INSTALL
Pitot cover--INSTALL
Cabin cover--INSTALL (if available)
Log books--FILL OUT
CLOSE YOUR FLIGHT PLAN

Aircraft Basic Knowledge Sheet

Dimensions: Height_____ Length_____Wingspan_____ Propeller_____Tires_____

Full fuel_____Grade_____POH endurance______TRUE endurance_____

Oil type_____Maximum_____Minimum______

Cockpit l switches, knobs, lights and sounds: ________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Gross weight _____Empty weight_____Full Fuel weight_____Cockpit load available_____CG Range_______

Speeds: Va_____Vx____Vy____Vfe____ Vne____Vno____Vg____

Calibrated vs. Indicated Airspeeds
Full Flap Configuration of C-152

CAS 43 51 61 71 82
IAS 40 50 60 70 80

Gross aircraft performance parameters in standard conditions:

Normal-Speed____

S.L. takeoff_____Over obstacle_____ Landing______ Over obstacle______Configuration ______________

Procedures_________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________

Short field-Speed____ Takeoff___Over obstacle ___Landing_____Over obstacle______Configuration_________

Soft field-Speed____ Takeoff___ Over obstacle___Landing_____Over bstacle______Configuration__________

Density Altitude Performance at Gross

Conditions: Level Cruise a 65% power, 7500' Standard Temperature.

True air speed______Fuel used____per hour

Takeoff at Gross Weight, 5000' 100 F, over obstacle Ground run______Rate of Climb_____ Total distance to 50'

Flying Safer
C-l52 will gain one inch of altitude for every foot of runway under standard conditions at sea level. At 5000' nearly two feet to gain that inch.

Consider checking the idle setting with the C.H. on to confirm the idle setting of the carburetor. A dead engine may still have a windmilling propeller. This is doubly important if you land without C.H. on.

Confirm that you have brake pressure as part of your pre-landing check.

Run your P-lead check of the magneto at idle then go to 1200 rpm before pulling mixture.

C-152 Spin Opinion
You are right about the 150/152 recovering just by relaxing the controls in an under 2 turn spin, with my instructor and me
putting the C of G on the forward limit you hardly have time to apply rudder opposite the spin before it recovers. I remember
the first spin I did with my instructor, the POH for the 152 states that "brisk application of down elevator might be needed
to break the stall" or words to that effect which might be true at an aft C of G but at a forward C of G.

I can personally confirm that a "brisk application of down elevator" will send every loose object in the cabin towards the ceiling including a rather startled instructor who probably cinches his seat belt a bit tighter when doing spins with new students now.

Approach Speed Opinion
My C-152 POH says 80 knots for the final approach speed minus 1 knot for each 100 pounds under gross. The stall speed of a plane, for level flight, is proportional to the square root of the weight. Since the approach speed is generally proportional to the stall speed, it is also proportional to the square root of the weight.

For a 152/150, with a 1600 gross weight, it would be closer to 1 knot lower speed for
each 60# less weight.

Return to whittsflying Home page
Continued on C-172